Round tube construction  Removable rails for ATV or utility use (Dual Rail Trailer)  Chopper Trailer accommodates up to a 90" motorcycle wheel base  Larger casters  Improved wheel chock system  Wider center-to-center rail width. Holds any size rear bike tire  Lower platform and longer ramps for easier loading  Full size spare tire mount  Folds up and stands up for easy storage  Double frame construction  Powder-coated finish  Chrome 13" wheels and tires  Independent rubber torsion suspension  E-Z Lube axle system  2" coupler  Platform: 5'x7' (Dual Rail Trailer)  1-year manufacturer's warranty on the trailer frame  5-year manufacturer's warranty on the axle * Trailer comes with 1 loading ramp. Must purchase additional ramp (77-5498) for ATV use

 High strength, lightweight aluminum  Skid resistant surface  Full platform for stability and footing  Folds in half for compact storage  2 handles for carrying  1-1/2" curb for edge protection  Folded dimensions: 55" x 36" x 6"  Weight: 68 lbs.  Special Order Only

 UPS shippable, when ordered individually  5-year manufacturer's warranty against defects "Heavy products shipping charge" "(+70)"

 Kit contains winch and cable, mounting post, electrical cables, control box and manual crank handle  Powerful 12 volt DC winch with 6000 lb. rolling load capacity  Hand-held winch control box with 20 ft. cord  Winch drum has 30 ft. of 3/16" aircraft cable and hook  Winch post clamps onto trailer tongue, no drilling, (hardware supplied)  Winch post attaches to all Kendon Trailers  Electrical power is supplied by vehicle battery  Connect the tow cable, hold onto your bike - winch pulls bike onto trailer

 Chrome-plated hitch plate  Made from heavy-duty steel and reinforced for extra strength, handles tongue weight up to 30 lbs.  Comes complete with 1-7/8" chrome-plated ball, mounting hardware and instructions  Necessary when using H-D fringed bags,H-D#90860-86

 Arching helps stop bottom dragging on tailgate lip with low-ground-clearance bikes  Made in USA with 6063T5 aluminum billet  .07" wall thickness  Robotically welded  10-year manufacturer's warranty against defects  Security straps included and are required when using product  Lightweight with vinyl-coated tips  1,500 lb. total capacity on arched ramp when used as pairs

 Full Dresser function with striking good looks  This hitch fits whether or not you have saddlebag light bars  Made of heavy-duty steel, it has a reinforced hitch plate and comes with all mounting hardware, including a 1-7/8" ball  Mfg/N 9181  Fits all 80-05 FLT, FLHT, FLHR models

 Made from top quality aluminum  Motorcycle ramp is 12" wide by 8 ft. long unfolded, or 53" folded  1000 lb. load capacity  Made in the USA

 Allows you to locate your motorcycle anywhere along the track for best position  Multiple motorcycles can now be quickly and easily installed in your trailer with optimum space utilization  With Series E Track already in place, there is no further hardware to install  Installation is easy: 2 clips and a pull of a strap and your chock is secured  Installs securely in both recessed and floor mounted Series E Tracks  Features a heavy-duty thick wall steel construction plated with a lustrous chrome finish, durable aluminum mounting plate and quality fasteners  Patent pending Does not come with track

 Arching helps stop bottom dragging on tailgate lip with low-ground-clearance bikes  Made in USA with 6063T5 aluminum billet  .07" wall thickness  Robotically welded  10-year manufacturer's warranty against defects  Security straps included and are required when using product  Lightweight with vinyl-coated tips  1,500 lb. total capacity on arched ramp when used as pairs

 12" x 89"  Ships UPS when ordered individually - truck freight for pallet  Security cables/straps included and required when using product  5-year manufacturer warranty against defect  Made in the USA  *Total capacity using pair of ramps, capacity is cut in half when used individually.

 Chock designed for corrugated floor  Complete with mounting plate  Mounting plate fits 3-1/2" & 6-1/2" wheel chocks  Made in the USA

 Raise or lower trailer tongue  Clamps on to most square or rectangular trailer tongues  Swivels out of the way when pulling trailer  800 lb. tongue wt. Capacity

 Features quick and easy installation and removal  Heavy-duty thick wall steel construction  2 sizes accommodate tire up to 6-1/2"  Chrome finish  Includes hardware  Made in the USA

 Change balls in seconds with only a few turns of the Reese Slotted Quick-Release stem  Requires no special tools  Has a unique design that permits the ball to spin freely on the shank to help eliminate annoying coupler noise and binding  Complete interchangeability, all balls fit on both 3/4" and 1" shanks  Comes complete with 1-7/8" and 2" ball

 Chrome-plated  Receptacle plate mounts below hitch plate for a quick, clean way to connect and disconnect trailer lights  Includes 5-pin connector wiring, mounting hardware and instructions  Fits Big Twin Touring models

 Uses a diving bell/trapped air system to keep bulbs dry and safe  All lamps are pre-wired for installation  Conforms to all applicable D.O.T. 108 regulations  Kit contains: 2 multi-function submersible taillights with gasketed lenses; 1 license plate bracket; one 20 wishbone trailer wiring harness, one 4 ft. trunk connector and accessory bag with frame clips and wire taps

TRAILER TIRES AND WHEELS

 Bolts directly to the floor of any truck, van or trailer  Features lustrous chrome-plated heavy-duty thick wall steel construction  Includes mounting bolts, nuts and washers  Made in the USA

 Mounts tire up and out from the trailer frame  Heavy-duty galvanized construction  Fits 4 or 5 lug wheels, tongues up to 3" wide by 4" high

 Converts foreign and domestic vehicles with separate turn signals to trailer lighting specifications  All electronic, 60" lead

 High speed replacement hubs for trailers  Fits 1" spindles  Complete with bearings, seals, dust cap and nuts

COUPLERS

 Low-profile, waterproof taillight  Replaceable sealed lamp capsule  Flush or recess mounting  15" pigtail and mounting hardware  8"L x 2-7/8"H x 2-3/4"D  Display packaged, sold individually

 Replaces dust cap on trailer hubs  Lubricates and protects bearings  2" O.D. sold in pairs  Includes protector covers

 Complete set of bearings, seals & dust cap for 1 hub  1-1/16" is for tapered spindle; 1" is for straight spindle  Sold individually

 Complete with all hardware and instructions  Blister packed for easy displaying  25 ft. with connectors

 Designed for a wide variety of trailers, including our Kendonr line  Meets D.O.T. requirements for: stop, turn, tail and side marker light, side and rear reflectors  Left hand has built-in LP illuminator  Compact design 4.7"W x 4.7"H x 2.8"  Push-in wiring connections  Mounts with 2-1?4" studs on industry standard 2" centers

 Extra length allows the handling of extra wide tires or wider tongues  Will fit either 4 or 5 hole rims

CHROME PLATED HITCH BALL

 Converts 7-way connector with blade type terminals to standard 4-way hat connector

 Fits all 1-7/8" to 2" couplers  Easy bolt-on installation  Makes moving trailer by hand much easier

 Replacement waterproof light capsule  Fits right or left Wesbar taillights  Sold individually

 4 ft. trunk connector  18" trailer connector

 Perfect for a wide range of trailer hook ups  Ideal for connecting electrical systems  Molded case ensures all year weather protection  Made in the USA

 Fits all low-profile Wesbar taillights  Order 1 for each light